Living Room finale

I've left the wall in the living room to cover HVAC lines forever, and since Christmas is coming we felt it was time to finish that.  Previously I had gotten drywall up:


Assembled new trim that's close to matching the existing chair rail:


Cut and painted baseboard:

Installed chair rail, baseboard and painted with primer.


And finished paint just before Christmas.



A few small things...

Decided while the 1st floor has been mostly done for awhile, staring at HVAC plumbing lines behind TV was old, so decided to box those in with drywall.  And of course none of the walls are plumb here... Hence the pieced-together 2x4 blocking.


Some drywall and mud, then good as new.


Also took opportunity to remove the last door on sunporch:


Fit new door in opening:

Shim and screw it in.



Snowblower sidetrip

You may recall that I rebuilt the snowblower this summer. And that went well.  I got things running, reassembled and ready.  And after a few months found this on garage floor:


Yeah, that's a leak. Turns out to be gear lubricant from the gear case, one of the few things I do NOT rebuild over the summer, so I guess I have a new project.

Time to take snowblower auger off:


Remove auger from housing:


And let's take it apart to see if there's a seal that can be replaced:


So take things apart, clean them out and order replacement lube and seals for gear box.


Oh? And see the green seal on the shaft below? That I can't replace because the impeller is completely rusted to the drive shaft.  I tried using penetrating oil and propane torch to heat impeller but that proved useless - the rust has fused these together.


Update: fully assembled and working, but I won't share how many times it took to get the driveshaft and augers assembled correctly (hint: neither the driveshaft nor augers are symmetric so there are many wrong ways to assemble them).




Glazed and Confused

Well, we decided the barn could just use more natural light.  Recall this past summer we added a new window to the barn. Well we could use another one.  Lather, rinse, repeat:

We need more light in the back wall on this side:


From barn, we have a couple of remaining old windows. So grab one and strip old paint:


Remove dried/cracked glazing from other side:


Invoke your inner child and roll out glazing like Play-Doh:


And mush it down at 45 degrees:


And we have a reglazed window. We need to let glazing dry (cure) for several weeks before we try to paint anything.


Sunday funday

We got most of drywall on first wall sanded, prepped and primed.


Most of wall primed - needed to cover the dark stain on lower wall as well.

Took advantage of some warmer weather to strip more shingles on back side wall of sunporch.


Last section with shingles to remove.


A little pre-rain fire.



Drywall

Maybe we've shared how much I enjoy drywall (I don't).  It's not terribly hard, but it requires a deft hand and technique that escapes me.  But it's a means to an end, so here we are.

The drywall in most of the room is in good shape, but the previous owner chose to use a textured finish, which we hate.  It's pretty hard to remove all of the texture (short of replacing all drywall) so the approach is to sand it and remove as much of high spots, and then go with a light skim coat of drywall mud over entire wall to fill in the low spots. A light sanding at end and it's pretty smooth.

The walls were a beige, so the white lines are from sanding high spots down:


Another view of sanded drywall:


After applying thin coat of mud (and no paint) wall almost looks like new drywall. It still needs a final light sanding.

And new drywall for slider wall:


Here's a better look at drywall sanding:



Sunporch windows

Spent time going back to my experience from over a year ago when we replaced 24+ windows. The first two windows are in sunporch, so now we build window jambs to fit.

My supervisor arrived on time.


Cutting jambs and filling holes and damage from prying off wall (all is reclaimed from trim we removed in this room).


Sanding jambs with my homemade downdraft sanding box.


Priming jambs before assembly.

And windowsills.


And jambs installed:





Sunporch progress

 Got a few loose ends tied up - finished Catherine's door before she returns for Turkey Break.


Started shingling the sunporch


Got some decent progress, but cold weather slowed things down.


Lots more shingle prep (gluing) in basement for trim under windows.


The previous owner had the drywall textured using drywall mud, which we dislike immensely.  S o started sanding to flatten things out.  It won't be perfect, but we can make things a lot smoother than they were.


Installed blocking for window jambs which are being assembled in basement (not pictured).



Slow sunporch progress

The weather wasn't super cooperative, and I was feeling lazy, so we didn't get a lot done this weekend.

Earlier in the week (wednesday?) we got one of the doors installed.


It actually went in fairly easily.


Temps are going to be colder next week so we needed to get trim and insulation for door and windows done while the weekend offered warmer-than-usual weather.

Assembled door trim in basement:


And voila trim installed (As well as spray foam insulation for cracks).


Spray foamed the windows and sliding door, let it set and trimmed excess (not pictured). And took time to cleanup the mess of tools and broken trim so we can work on window trim soon.




Moving backwards

 

Still work to be finished, but got the scaffolding removed. Some paint and trim on the portico and we'll be in a better place.


So we moved back to the sunporch. Here's the current state:


First removed all shingles.


And then the casement windows.

Goodbye old windows.


Hello Tyvek.


And some new windows with trim.



Garage, other side, part deux

We don't have a ton of pictures even though good progress was made.   Short story: we finished all the termite damage replacement, simil...