Garage, Sun Porch, Basement and more.

A hodge-podge of things this weekend.

Sunporch finished first round of drywall and sanding, so primer and caulk.



Actually using garage lift to move a bunch of furniture:


Building supplies (mostly shingles):


Plumbing (pex, garden hoses and drain):


I finished a cross cut sled for table saw:


Painting another window for garage


Replace some broken glass with glazing points and compound:



Garage Hoist? check!

Houston, we have liftoff.

Check pulley and cable alignment with platform and joists.


Built the connection (aka: "manifold") between 4 platform cables and winch cable.

Attach all pulleys and run cables:


Some assembly required to attach cables to platform.


And HOLY COW, this works.


Office Floor Fiasco and Minor Outdoor Progress

Was lazy this weekend and didn't get a ton done, but we were able to fix a minor problem that came up, and work on something that's been waiting awhile.

We had bought a mat to trap cat litter under litter boxes.  And that works, but you can't vacuum it well, so you have to remove the mat and shake it outside to clean periodically.  This was the first time I attempted to clean it and then things went south.  The mat has a rubber backing so it doesn't slide on wood or tile floors - except the rubber backing came off and stuck to the polyurethane on the floor.


So we scraped as much of rubber backing off the floor and then sanded the remaining debris:


And finally reapply polyurethane

Most work on the portico has stopped due to winter weather, but I had the PVC trim boards for the two columns stacked in sunporch, which were in the way when working out there. So I decided to get those posts wrapped with trim.

Before:


After:

IF you have a really good eye, you'll see the screw holes on one side are not filled yet - they will be.

Garage Fun + More

We have more progress on garage. 

First, we were able to fix the cracked electrical box on the hoist (winch) with a couple of screws.


Mounted the hoist on a section of 2x8


And mounted hoist on the garage wall.


Mounted pulleys in garage joists and then hung a weight off a rope around pulley to check alignment with joists.


Started on cables connecting 4 platform cables to the adjustable eye bolts.  We'll mount those on pulleys in garage and then cut other end of cables to length.



Garage Hoist Platform (and hoist?)

We assembled the platform for the garage hoist.

Screw platform members together:


Put 3/4" plywood deck on:

Install eye bolts

 and cut off extra length.


WE received the hoist, but the electronic box (black) doesn't appear to be attached properly. So we're contacting customer service.



Beach Side Trip

We need to replace the kitchen gas stove at beach, because this one is failing after 30+ years (it's old). From original purchase of house in 2016:


We've since had counters replaced in 2020, but now it's time for the stove itself.


Under burners are rusted and pretty tired after a few decades of use.


A skinny opening for new 24" stove: 


I've since removed the old electrical outlet (no longer in use), shortened the gas line and had proper shutoff installed.


More Garage Framing

Some additional components added for hoist.

Current space with ladder won't change.


Unfortunately, where the new 2x6 supports land, neither had good vertical supports on center wall. So we added a proper header for the large (4') opening, and a pair of 2x4 vertical supports where horse "jail" pipes are located.

We then added the blocking across ceiling joists where cable pulleys will attach after some careful measurements.


We continue to pile up hardware from pulleys, bolts, cables and more.


And return things that were incorrect (from manufacturer, not me).




Garage Hoist Framing

First we need to add two pairs of 2x6 joists, and then run two vertical supports up to roof joists that will carry the load from the hoist.

This is the first horizontal support and then the two vertical supports run up to roof joist directly above it.


This is from loft looking down - the two horizontal supports are installed and level, but the vertical support is only on the right side at this point.


Here you can see both horizontal supports and all vertical supports run up to roof rafters


The hoist will run right in the middle of the four vertical supports.


Garage Hoist (?!?)

I watch a fair amount of YouTube videos because hey why not? You can learn stuff.  And last week a collision of my desires and need came together on YouTube.

We have a lot of stuff to store, for long and short term. And we have a lot of storage space in the garage/barn loft.  But the reality is getting heavy items up into the loft is nearly impossible.  Well, until you steal ideas from YouTube.  Like a garage lift.

So the concept isn't hard once you understand the design.  After lots of thinking and measuring the concern I have is that the roof joist maybe slightly undersized in the barn (considering possible snow loads) - and that's before using them to support a garage lift capable of lifting 500lbs.

The short answer is I need to add some framing to provide additional support to roof joists where the lift will be and things should be fine. Here's the loft before - we'll remove one section of the railing to open access.


Here you can see two 2x6 horizontal supports, we'll be adding more and then using those to support roof joists.


Here's the expanse of roof joists before we add any support to them. (and remove weeds that grew inside the wall)




Several Tasks

Lots of random things going on, trying to keep many projects moving.

After much siding work, I was able to sell the scaffolding, pump jacks and aluminum plank.  That's gonna pay for another project (garage hoist?).


Leveled (plumbed) the sliding doors:


Installed the astrigal (divider that connects two doors in middle).


Took advantage of warmer weather to put drywall mud on second wall as we try to remove texture from previous owners. Once it dries, we lightly sand and then prime the walls white.


And building a cross cut sled for my table saw, something that's long overdue.  Cut to size and dado slots:


Adding T-track into slots and epoxy them in place.  This will allow a number of hold-down clamps and other gadgets to be attached to the sled later.



Garage, other side, part deux

We don't have a ton of pictures even though good progress was made.   Short story: we finished all the termite damage replacement, simil...