Beach Paint

Short update: Got some more cleanup and paint done.

Painted a few ceiling tiles that were badly stained.  They match much better now.


Toilet/sink wall painted.


Behind washer/dryer also completely painted.



Beach Basement Bathroom, part 3

More bathroom progress.

Installed new lock/deadbolt on all doors.


Filled old floor drain and door track with concrete to level floor.

Flashing above door.  We also painted  all trim and spray foam (not pictured) grey so it doesn't stand out as much.


First coat of paint on new basement door to match others.


Beach Basement Bathroom

We got the basement door replaced last week, now time to start tackling the bathroom which was long overdue for some love.

Remove sink:


Remove toilet:

Remove washing machine


Shuffle washer into other room.  We need to do a small repair on dryer and this will make access easier.

Now start chipping out tile:


Voila, tile all gone:



Beach detour

While we have no shortage of home projects, we have a couple of beach things that have been lingering.  The most important is to get the downstairs flooring replaced to match the upstairs from last winter.  However, the downstairs bathroom and exterior door needs some love, and we need to get that done before the flooring can move forward.

Let's replace a door.

Buy a door (that fits the opening you already measured many times).


Strip trim from old door.


Remove old door.


Cleanup all scrap for disposal.


Remove old adhesive and schmoo from concrete.



Install new door and level.


Lots of loose ends, but just replacing the door makes a huge improvement.


Gotta finish the sun porch

We need to finish the sunporch, for many reasons.  So lots of small items to address...

First we must have trim under the doors to the ground "for support", says the building inspector. (eye roll)

Drill some hole in concrete.

Install two small blocks to create a flat mounting surface.


Install final trim under door.  We touch up blue screw heads with a quick shot of white spray paint.

I won't repeat all of the above but the steps are 100% the same to mount trim under sliding door.


Have I mentioned how much I hate the look of this under the door and that it doesn't align with the other trim?  We deliberately don't want to run trim boards down that low on house for many reasons...


Shed final work

We cleaned up the shed this summer for storage, but it had no doors. So we made some.

Lots of glue to frame edges in 2x4:


Screw things together, and let glue dry.


Lots of sanding and paint.  Then we go from this:




Hang doors and voila.



WE have ... a dock?

Looking around and talking to neighbors, I realized others have docks or access to pond.  This led to dock-envy so let's go.

After some debate how to get posts in water, we decided to go with PVC pipe fill with concrete.  This seemed better for pond life than immersing arsenic-dowsed wood in pond for years.

Since we're in a drought, we were able to dig with post hole digger directly in pond and drive PVC posts in.  Mix some concrete and fill post.


We pre-drilled holes for bolts before pouring concrete, so securing 2x6 to each post only took a few minutes.


Add some deck board and voila, instant dock.  Now if only the water would come back.



Planing Trim

When  you work with reclaimed wood, you need to clean it up.  That means cut to size and resurface both sides to remove old/dried wood.

We've gotten good use from a Grizzly planer over 3 years, but that luck ended last week.  During routine sharpening of blades a screw became stripped and then wouldn't seat properly.  And when you operate something that spins at 10000 RPM with a screw missing, bad things happen.

The broken metal below is one of the blades and mounting bracket.  The cost to repair this would exceed a new planer, unfortunately.


Sadly, this ended up straight into the trash. :(

But that means we get a new one and we're going with the same model that the rest of the world seems to love: Delta.

Of course it's brand new, but it cuts smooth as butter and has a few features the old Grizzly did not.  So we're back in business after a one week hiatus. 

Milling Sunporch Trim

We need to close out the building permit, and the last thing left is finishing trim in the sunporch.  So we begin to cut and mill reclaimed wood for this purpose.

First we measure all doors/windows and make a list of trim needed.

We then grab all the reclaimed wood, measure and try to fit the existing pieces against the needed trim list.


We quickly cut boards to the desired width and approx length.


We have some other leftover pieces that are too short, so we cut the half lap joints:


And glue them up to make longer trim pieces.


We'll then begin the process of planing all these down to the same thickness.  But the next post will explain the hell that caused.




Outdoor Work

And handful of outside activities moving forward...

Finish shingle over the sunporch.


And add trim on both sides.



Glue up long thin strips of shingles


And apply under windows - often thin shingles split when just nailed individually.  Before:


After:





Let There be Light

So with a lot of investigating, we figured out every wire in the sunporch with the exception of one.

We need to make the existing can light openings larger. So we first attach a 2x4 and find the center of the existing hole.


We use the hole saw for new lights to make the opening an inch larger.


Yeah, drywall is dusty.


Reattach all wire and install the new driver boxes.


Apply ceiling paint before we install fixtures.


And install the fixtures.

We clean up the wiring from this:


To this:


And it's brighter than a runway now.






Garage, other side, part deux

We don't have a ton of pictures even though good progress was made.   Short story: we finished all the termite damage replacement, simil...