Kitchen Cabinets

 We have the main wall of cabinetry installed.  We got the upper cabinets installed a few days ago, and completed the lowers this weekend.  

Here are the uppers:


And completed with lowers starting in the corner:


Complete set:

The kitchen floor is out of level by almost 1 1/2" across the cabinet run.  Because of this, it would be nearly impossible to shim them up 1 1/2" on the low end to make them level.  Instead, we measured and cut the base of each cabinet to lower the high ones down almost 1 1/2".  This took a lot off the bottom of some on the right side above:


That's a lot removed from toe kick (but very necessary).

The end result is that the cabinets are nearly perfectly level, give or take 1/16" of an inch.  When countertops are ordered, they should be an easy install.

Kitchen Floors Mostly Complete

 We've made good progress in last few days and all smiles.

We have the entire kitchen pine floor laid.  It still isn't sanded, stained or urethaned, but it's completely installed.  This is last few boards heading into pantry:


The "runway" thru center of kitchen

Last boards being installed by dining room wall.

Some of the HVAC registers I bought - they're made of pine so they can be stained and urethaned to match floor.



A router tale...

 Time for a sidebar.

When we bought first house back in 1998 my parents bought me a 2hp Craftsman router with a router table.  It was an interesting gift - I was a hobbiest woodworker and can't say that I had need for a router that often.  But it's a tool that is indispensable for certain tasks.  I've had the router and table for 22 years now.

When we bought this house the 60 year old kitchen floors, while worn, were amazing (see them above, on the right).  I knew with a planer I could resurface the backsides and then cut tongue/groove with router and make them look great. So having a working router and table was a necessity to complete the kitchen floors.  About 2 months into the project, my old router started having issues.  I couldn't remove the 1/4" collet and install the 1/2" collet, required for the tongue and groove bits I bought:


After a few days of on/off fighting I was able to resolve the problem and got it working. It worked fine for about 2 months of hard use.  But this morning I had trouble adjusting the height.  The adjustment ring is officially broken, even though the motor works fine. Unfortunately, a router without a height adjustment is about as useful as a boat motor with no propeller.

I had already bought a new router, but it won't mount on my router table (because the router table was designed 22 years ago and doesn't fit newer style router face plates).  Fortunately, the router table top is made of aluminum, so I was able to easily drill new holes in it to match those in the new router:


A trip to hardware store to purchase three screws for $1.35 and voila - new router mounted in old table. And we're back in business.  Was able to cut tongue and groove in the largest piece of pine flooring which measures 12 feet long by 20" wide.  And finally get the behemoth installed (the leftmost board below)



Kitchen Upper Cabinets and Vent Hood

 We started to install the upper cabinets and after much consideration, changed plan for the vent hood.  The original plan for the hood was something like this:


For a variety of reasons (low ceiling height, joist directly over range, etc) we dumped the taper and will go with a straight hood, more like this:

Upper kitchen cabinets:



New hood framing:






Kitchen Drywall

 We managed to get drywall up in kitchen and now start the process for planning cabinet runs and hood.




The hood will look something like this (without the formal crown molding,)

We start by getting the hood framework positioned correctly:

It's a touch lower than I might like, but the low ceiling height and exposed joists don't give us a lot of leeway to go higher.  For comparison, there will be approx 21" clearance between vent hood and cooktop, almost 6" more than we have now with microwave over the range (which is WAY too close)







Laying Kitchen Floor, 2

Laying the floor is a bit slow, but we're making progress.  As I mentioned, even slight differences in planing thickness make fitting boards together difficult.  Moreover, any slight curves also complicate matters.

I managed to setup my router to serve and resurface the super wide boards.  Here's some great time lapse of them:



And a side view:


The before/after comparison:


After surfacing, and some sanding, we have some pretty sexy wide pine flooring:




Laying Kitchen Floor

We were finally able to start laying the kitchen floor.  Installing it wasn't hard, but the details of floorboards which have minor curve in them or slight planing differences quickly make themselves known.  All in all, we only have a couple of minor hiccups and, in general, the first section went down pretty well.

I bought a tongue and groove router bit set from MCLS:


The details of cutting tongue and groove aren't terribly difficult, but even minor differences in thickness cause some misalignment.  But we worked through those and installed the first row by face nailing along the wall edge.  The first board also needed two holes for HVAC ducts.


After installing the first 7 boards in the sitting area, we stepped back to admire our work:


Insulation

 We finally got spry foam insulation completed today.  This was to insulate several areas of house while walls were open.

Attic insulation to help protect HVAC equipment and save heat loss from 2nd floor:



Eaves against closet/2nd floor bedroom




2nd floor bathroom:


Kitchen insulation:



Kitchen Floors, 3

 As we get closer to possibly installing kitchen floors, we now begin the process of inventorying each piece of cut/planed flooring and then laying out where they will fit best.  Best, meaning they are used almost in their entirety, and don't leave too many cuts (we don't want to splice together 10 small pieces for any one length).

This is grouping of 8-10 boards salvaged from barn.  The widths vary a little in this group from 9" to 11"

This is the collection of boards salvaged from original floor.  These are all cut to same width, approx 12 1/4"

These are the super wide original floorboards - we have three that are between 19" and 20" wide.  Due to their excessive width, we have to plane these with a small electric hand planer.  The small pile of 4 board on left are last boards from barn yet to be cut/planed:

From the three groups above, I built an inventory of each board and assigned a unique letter to each:

12 3/16 width:

*A 69.5”
*B 65”
*C 50”
*D 164”
*E 136”
*F 128”
*G 127”
*H 90”
*I 85”
*J 77”
*K 82”
*L 68”
*M 132” 5/8” thick
*N 138”
*O 138”
*P 136”
*Q 155”

Others
*T 126” x 10.25”
*U 128” x 9”
*V 128” x 10.25”
*W1 128” x 11”
*W2 128” x 11”
*W3 128” x 11”
*W4 128” x 11”
*X 110” x 9.5”
*Y 81” x 9.125”
*Z 68” x 10.25”

Oversized (widths
AA 128" x 19"
BB 127" x 19"
CC 129" x 20"

I sat down in did a scale drawing of the kitchen (down to an inch or so) in LibreCAD and then began the layout of boards.  From what I was able to piece together, I need about 4 more boards - hence the 4 above that need to be cut/planed.



Kitchen Floors, 2

The work to prepare floors for kitchen is a bit, given that we're trying to save as much of the original 60+ year old floors as possible.  The idea is we trim each board side to get clean edges, plane the backside smooth until board is 3/4" thick, then use router to get tongue/groove slots in edges so they fit together cleanly.  We don't want to face nail them, but I don't mind all the old nail holes showing.

This is trimming edges:


This is planing thickness down to 3/4"

This is what planed boards from original kitchen floor look like with no stain/finish on them - they're quite "blonde" and rather uniform in color, aside from knots:




This is what reclaimed boards from barn look like - they're all pine, but different age and tree selection.  These have a lot more color variation in them:




Garage, other side, part deux

We don't have a ton of pictures even though good progress was made.   Short story: we finished all the termite damage replacement, simil...